Apparatus_Purchase_Agreement_FountainHills Rev 1

Town of Fountain Hills — Town Council (2026-11-17)

View PDF Meeting page

Extracted text (via pymupdf_layout) 82561 characters
APPARATUS PURCHASE AGREEMENT
This Apparatus Purchase Agreement ("Agreement") is entered into by and between Fire Truck Solutions, LLC, a Delaware limited
liability company ("FTS" or "Company"), and the customer identified below ("Customer"). FTS and Customer may be referred to
collectively as the "Parties."
1. Apparatus and Purchase Price
Fire Truck Solutions, LLC ("FTS" or "Company") agrees to sell to the customer identified on the signature page ("Customer"), and
Customer agrees to purchase from FTS, the fire apparatus, chassis, equipment, options, and accessories described in the final
specifications attached as Appendix A (collectively, the "Apparatus"), for the purchase price stated in the applicable proposal, quote,
order acknowledgement, or pricing exhibit incorporated into this Agreement (the "Purchase Price").
Unless expressly stated otherwise in writing by FTS, quoted pricing is based upon manufacturer pricing, component costs, freight,
tariffs, taxes, governmental charges, and other costs known as of the quote date. Any customer-requested change,
manufacturer-mandated change, change in law, tax, tariff, freight charge, or other cost increase occurring after execution may result
in an equitable adjustment to the Purchase Price upon written notice from FTS. Applicable sales, use, excise, registration, title, or
similar taxes and governmental fees are the responsibility of Customer unless expressly included in writing.
2. Specifications and Order of Precedence
The final written specifications approved by FTS and Customer and attached as Appendix A shall control the configuration and
construction of the Apparatus. In the event of a conflict, the following order of precedence applies: (a) a later written Change Order
signed by FTS and Customer; (b) this Agreement; (c) Appendix A final specifications; and (d) any proposal or other incorporated
exhibit. Oral statements, demonstrations, marketing materials, preliminary specifications, and prior correspondence do not modify the
final specifications or this Agreement.
3. Estimated Completion and Delivery
Any completion, production, or delivery date stated by FTS is an estimate only and is not a guaranteed or "time is of the essence"
obligation unless FTS expressly agrees otherwise in a writing signed by an authorized officer of FTS. Delivery timing is dependent
upon manufacturer production schedules, chassis availability, component availability, transportation, inspections, customer
approvals, and other matters that may be outside FTS's control.
FTS will use commercially reasonable efforts to coordinate delivery. FTS is not liable for delay damages, liquidated damages,
penalties, consequential damages, loss of use, substitute equipment costs, lost revenue, or other damages arising from delayed
production or delivery. A delay does not entitle Customer to cancel the order unless FTS expressly agrees to cancellation in writing.
4. Force Majeure and Excusable Delay
FTS shall not be responsible for any failure or delay caused in whole or in part by events beyond its reasonable control, including acts
of God, fire, flood, severe weather, natural disaster, epidemic or pandemic, war, terrorism, civil unrest, labor dispute, governmental
action, regulatory delay, transportation disruption, material or component shortage, supplier or manufacturer delay, chassis shortage,
supply-chain disruption, cyber incident affecting a supplier or manufacturer, utility interruption, or other similar cause. Any affected
schedule shall be extended for a commercially reasonable period.
5. Change Orders
No change to the Apparatus, specifications, Purchase Price, payment terms, or other material term is binding on FTS unless
documented in a written Change Order or other written amendment approved by an authorized representative of FTS.
Customer-requested changes may affect price and schedule. FTS may make non-material substitutions or changes that do not
materially diminish the Apparatus's intended function when reasonably necessary because of component availability, manufacturer
changes, regulatory requirements, or product obsolescence.
6. Payment Terms
Customer shall pay FTS in accordance with the payment schedule stated in the applicable proposal, invoice, or pricing exhibit.
Unless a different written schedule is incorporated into this Agreement, the unpaid balance is due upon notice that the Apparatus is
ready for final delivery or acceptance, and in all events before transfer of title unless FTS approves other terms in writing.
Customer may not withhold, offset, or deduct amounts from sums due to FTS based on disputed items, warranty claims, or alleged
defects, except to the extent required by applicable law. FTS may suspend performance, withhold delivery or title, and/or exercise
any other lawful remedy if Customer fails to make a required payment.
7. Inspection, Acceptance, and Punch-List Items
Customer shall inspect the Apparatus promptly upon delivery or at any final inspection made available by FTS or the manufacturer.
Customer must provide FTS written notice describing any claimed material nonconformity within ten (10) calendar days after delivery.
If Customer does not timely provide such notice, the Apparatus will be deemed accepted.
FTS Generic Apparatus Purchase Agreement Page 1

Minor defects, adjustments, warranty items, or punch-list items that do not materially impair safe operation of the Apparatus do not
constitute grounds for rejection, cancellation, or withholding the Purchase Price. FTS shall have a reasonable opportunity to correct
any timely reported material nonconformity. Customer's use, registration, placement into service, or resale of the Apparatus
constitutes acceptance.
8. Title and Risk of Loss
Title to the Apparatus remains with FTS until FTS receives all amounts then due under this Agreement in collected funds. Risk of loss
will pass to Customer upon delivery to Customer, Customer's carrier, or another delivery point designated by Customer, unless
otherwise expressly agreed in writing. Customer shall maintain appropriate insurance from the time risk of loss passes.
9. Warranties
FTS will administer and coordinate applicable manufacturer and component warranties identified in Appendix B or otherwise
delivered with the Apparatus. Except for any separate written warranty expressly issued by FTS, FTS does not expand, modify, or
independently guarantee any manufacturer's or supplier's warranty.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, ALL WARRANTIES NOT EXPRESSLY STATED IN THIS AGREEMENT OR IN
AN APPLICABLE WRITTEN MANUFACTURER WARRANTY ARE DISCLAIMED, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Warranty remedies are subject to the terms, exclusions,
limitations, and procedures of the applicable warranty.
10. Limitation of Liability
TO THE MAXIMUM EXTENT PERMITTED BY LAW, FTS SHALL NOT BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF USE, LOST PROFITS, LOST REVENUE,
LOSS OF SERVICE, SUBSTITUTE APPARATUS OR RENTAL COSTS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, FTS'S AGGREGATE LIABILITY ARISING OUT OF OR RELATING TO THIS
AGREEMENT SHALL NOT EXCEED THE AMOUNT ACTUALLY PAID TO FTS FOR THE SPECIFIC APPARATUS GIVING RISE
TO THE CLAIM. Nothing in this section limits liability to the extent a limitation is prohibited by applicable law.
11. Cancellation and Customer Default
Because fire apparatus are custom-built and commitments may be made to manufacturers and suppliers immediately after order
placement, Customer may not cancel this Agreement for convenience without FTS's prior written consent. If FTS agrees to a
cancellation, Customer shall reimburse FTS for non-refundable manufacturer or supplier charges, completed work, special-order
materials, freight, administrative costs, and other documented costs or commitments incurred in connection with the order.
If Customer materially defaults and fails to cure within a reasonable period after written notice, FTS may suspend performance,
terminate the Agreement, retain amounts lawfully due, and pursue its available legal and equitable remedies. This section is intended
as reimbursement and preservation of remedies, not as a penalty.
12. Customer Responsibilities
Customer is responsible for timely approvals, information, decisions, access, inspections, financing, tax-exemption documentation,
and other cooperation reasonably required to process and complete the order. Delays attributable to Customer may extend the
delivery schedule and may result in additional costs. Customer is responsible for ensuring that the Apparatus configuration selected
by Customer is suitable for Customer's intended operations, local requirements, staffing, loading, and use, except as expressly stated
in the final specifications.
13. Authority
Each person signing this Agreement represents that he or she is authorized to bind the Party on whose behalf the Agreement is
signed. Customer represents that it has completed all approvals, appropriations, procurement steps, and other actions required for
Customer to enter into and perform this Agreement.
14. Entire Agreement; No Reliance
This Agreement, together with its incorporated appendices, exhibits, proposals, and signed Change Orders, constitutes the entire
agreement between the Parties concerning the Apparatus and supersedes prior or contemporaneous discussions, negotiations,
representations, and understandings concerning the same subject. Customer acknowledges that it is not relying on any
representation or promise not expressly included in the Agreement documents.
15. Notices
Notices required under this Agreement shall be in writing and delivered by personal delivery, nationally recognized overnight carrier,
certified mail, or email with confirmation of receipt to the addresses stated on the signature page or to another address designated by
written notice. Notices are effective upon receipt.
FTS Generic Apparatus Purchase Agreement Page 2

16. Governing Law and Venue
Unless FTS agrees otherwise in writing, this Agreement shall be governed by the laws of the State of Arizona, without regard to
conflict-of-law principles. Any action arising out of or relating to this Agreement shall be brought in a state or federal court having
jurisdiction in Maricopa County, Arizona, and Customer consents to such jurisdiction and venue. If applicable law requires a different
venue or governing law for a governmental Customer, the mandatory requirement will control only to the extent required by law.
17. Attorneys' Fees and Collection Costs
To the extent permitted by applicable law, FTS shall be entitled to recover its reasonable attorneys' fees, collection costs, court costs,
and other expenses incurred in collecting overdue amounts or enforcing Customer's payment obligations. In any other action arising
from this Agreement, attorneys' fees and costs shall be awarded only as provided by applicable law.
18. Assignment
Customer may not assign this Agreement or its rights or obligations without FTS's prior written consent. FTS may assign this
Agreement, receivables, or performance obligations to an affiliate, financing source, manufacturer, successor, or purchaser of
substantially all of the relevant business or assets, upon written notice where required by law.
19. Miscellaneous
If any provision is held invalid or unenforceable, the remaining provisions remain in effect. A waiver is effective only if in writing and
applies only to the specific instance stated. Headings are for convenience only. This Agreement may be executed in counterparts and
by electronic signature, each of which is deemed an original. No third party is an intended beneficiary of this Agreement. Provisions
that by their nature should survive completion, delivery, acceptance, payment, or termination shall survive.
CUSTOMER / ORDER INFORMATION
Customer Legal Name: Fountain Hills Fire Department
Customer Address: 16426 E Palisades Blvd, Fountain Hills, AZ 85268
Apparatus Description: E-ONE Cyclone Custom Cab Pumper
Proposal / Quote No.: 148568
Purchase Price: $1,293,637.00
Payment Schedule: Due Upon Delivery
Estimated Delivery: August, 2028
Customer Notice Email:
CUSTOMER FIRE TRUCK SOLUTIONS, LLC
By: By:
Name: Name:
Title: Title:
Date: Date:
FTS Generic Apparatus Purchase Agreement Page 3

APPENDIX A - FINAL SPECIFICATIONS
Attach applicable documents here.
FTS Generic Apparatus Purchase Agreement Page 4

Date Printed: 2026-08-24 at 18:46:28 EDT Username: john.navarro P/N: S149682 Creator: Griffin, Noah Version: A.1 State: In Work Context: Pumper
Location: /Default/149000/149682/Sales Drawings

Date Printed: 2026-08-24 at 18:46:28 EDT Username: john.navarro P/N: S149682 Creator: Griffin, Noah Version: A.1 State: In Work Context: Pumper
Location: /Default/149000/149682/Sales Drawings

RIO RICO FIRE DISTRICT
RIO RICO, AZ
PPL.149682
CERTIFICATION
PUMP MODEL G.P.M. @ P.S.I. @ ISSUE DATE R.P.M. Do reaches to be NOT completely full exceed level. max evacuated Continue ! fill pressure. 9#40+0) filling by overflow at Gate a rate back pipe. which flow Water will into should allow tank excess before not be water tank WATEROUS CSU
G.P.M. G.P.M. @ @ P.S.I. P.S.I. @ @ R.P.M. R.P.M. allowed Failure over-pressurization to to follow spill from these and the manufacture's tank tank fill failure. tower. Direct instructions any inquiries could result to UPF,inc. in
G.P.M. @ P.S.I. @ R.P.M. at Over-pressurization 800-638-8265 of tank will void warranty. 1047175
CERTIFICATE NO. SERIAL NO.
SERIES/PARALLEL GOV. SPEED 240086
(FOR INTERNAL SALES PURPOSES ONLY)
john.navarro
A.2
Username:
Version:
*;&4#7.+% '37+2/'06 4#%-
! 9#40+0) 57&&'0 14 &'#6* 4#%- /18'/'06 /#; %#75' +0,74;
%.15'& &1145 (14 /756 4#%- $' 61
12'4#6' 10 72
%.'#4 $' 574' 1( #4'# +5
2'45100'. 12'4#6+0) $'(14'
647%- &1 016 70.'55 /18' 4#%- 4'#&; 1(( &190
+5 5'%74'
DISCHARGE 4 DISCHARGE 3 DISCHARGE 2 DISCHARGE 1 EDT
HALE EZ FILL
'0)+0' 42/ Nelson,David
EDUCTOR 5'66+0) 25+
24'5574' %10641. # / PUMP COOLER
27/2 $155 /#:
1- 61 27/2 6*4166.' 4'#&; 18:46:36
TANK TO PUMP
24'5'6
24'5574' 42/
DEF FLUID Pumper
/ ' 0 7 +&.' 4" DISCHARGE
HOSE REEL
at
/Default/149000/149682/SAE
Creator:
Context:
INTAKE
2026-08-24
FOAM FILL
Work
PPL149682
Printed:
In
FJL PRECONNECT 2 PRECONNECT 3 LFHB INTAKE
DISCHARGE 4 2.5 CROSSLAY DECK GUN DISCHARGE 3 DISCHARGE 2 DISCHARGE 1 4" DISCHARGE
Location:
State:
Date P/N:

Date Printed: 2026-08-24 at 18:46:29 EDT Username: john.navarro P/N: L149682 Creator: Griffin, Noah Version: A.1 State: In Work Context: Pumper
Location: /Default/149000/149682/SAE

Prebuild Meeting Change Requests
Customer Name: Fountain Hills Fire Department
Shop Order (SO) #: 149682
Quote #: 148568
Quote Revision Level: 41
Sales Drawing Revision Level:
Prebuild Date(s): 9/29/2026
Attendees: E-ONE - J. Navarro
Fire Truck Solutions - M. Julien, J. Julien, S. Kern
Fountain Hills FD - J. Krajnak, B. Linden
NOTE: The following changes are being requested to the vehicle(s) purchase contract. Requested changes will be submitted to E-ONE’s
Sales Administration group for addition and/or deletion to the vehicle purchase contract. The vehicle configuration and price will be
adjusted. Some or all changes requested may require a formal assessment by one or more of E-ONE’s Engineering Teams. Items reviewed
by engineering will be examined in the context of the purchased vehicle’s configuration for feasibility with the intent of instituting the
requested change. Size, weight, availability, location conflict along with other pertinent data such as NFPA and FMVSS requirements will be
considered. Some or all requested items may be determined to be unavailable and subsequently declined. Change Request(s) (C.R.s)
posting will be monitored by the Dealer and the Dealer will communicate change determination(s) to the purchaser.
Salescode Extended Description Qty Prebuild Changes Notes
TESTING COMPLIANCE STANDARD
1001-0103 The E-ONE supplied components of the vehicle shall 1
meet the requirements of NFPA 1900, 2024 edition.
3090-0003 OAH RESTRICTION. The unit has an overall height 1 10ft. 10in.
restriction and the height is not to be exceeded
(unloaded condition).
3090-0005 OAL RESTRICTION. The unit has an overall length 1 33ft. 0in.
restriction. The length is not to be exceeded.
3090-0006 The hose bed is to have the capacity for the following 1 Lay 1 - 200 ft. of 1.75 DJ Lay 2 -
hose. Hose load shall be listed from driver to officer. 900 ft. of 3.00 DJ Lay 3 - 650 ft. of
4.00 DJ Lay 4 - 300 ft. of 3.00 DJ
Estimated Weight - 1545 lbs.
Page 1 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3340-1137-12B Equipment allowance on the apparatus shall be 2000 lbs. 1
This allowance is in addition to the weight of the hoses
and ground ladders listed in the shop order as applicable.
INSPECTIONS AND PENALTIES
1002-0001 Final inspection trip. 1
1002-0003 Unit has a penalty clause. 1
CHASSIS PREP
1020-0053 Gates Green Stripe hose IPOS (silicone hose) shall be 1 Manual added by ARIOSECO on 19-
used for coolant applications throughout the cab and MAR-26
chassis, where available.
BUMPERS
1160-0008 3/16" Front Bumper Gravel Shield. 1
1160-0208 22" Front Bumper Gravel Shield Extension. 1
1160-0345 Heavy duty, formed, 10" front bumper with full wrap 1
around. Corners to be tapered for up to an 8.5" wide
mounting area (Units with drop style frame extension
and recess notch mayl reduce size of mounting area).
Includes support wings for outboard sides (as
applicable) To be painted job color unless
BUMPER TRAYS
1150-0170 Bumper tray center of bumper without slats 14 inches 1
deep.
1150-0357-000-13 Turtle Tile Brand Black floor matting covering on center 1
bumper tray floor.
1150-0459 Black nylon cargo net on center front bumper tray. The 1 Manual added by ARIOSECO on 05-
cargo net shall be connected up front with a min. of two SEP-25
(2) footman loops and in the rear using a min. of two (2)
buckles. Female buckle attached to netting and male
buckle to be hinged and attached to gravel shield/top of
tray area
FRAME ASSEMBLY
1250-0011 Rear underbody support frame. 1
1250-0080 Frame assembly with 10.25 x 3.5 x .375 powder coated 1
galvanized rails.
1250-0092 GEOMET coated frame assembly fasteners. 1
AXLE OPTIONS
Page 2 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1025-0028 Koni shock absorbers for front axle - adjustable. 1
1025-0030 Stemco sight glass for front axle hubs. Inboard wheel 1
seals will be Chicago Rawhide (or equivelant).
1025-0089 Meritor RS-26-185 single rear axle 27,000lb capacity 1
1025-0209 Meritor FL-943 front axle 20,000 lb. Includes 1
maintenance free bushings.
SUSPENSIONS
1070-0012 Reyco rear suspension springs rated equal to the 1
capacity of the axle. Can only be used up to 31,000.
WHEEL OPTIONS
1050-0001 Alcoa aluminum wheels for front axle (2). 1
1050-0003 Alcoa aluminum wheels for rear axle (4). 1
1050-0007 Front axle wheel trim kit. Includes stainless steel lug nut 1
covers (chrome plated plastic if applicable) and center
cap with E-ONE logo. Note: Center cap will have an
inspection port IPO a logo if equipped with Stemco oil
seals.
1050-0008 Rear axle (single) wheel trim kit. Includes stainless steel 1
lug nut covers (chrome plated plastic if applicable) and
center cap with E-ONE logo. E-ONE custom chassis
w/steel wheels will have chrome plated plastic lug
covers.
1050-0017 Each inside wheel of the single rear axle shall have valve 1
stem extensions.
TIRE OPTIONS
1060-0005 Four Michelin 12R tires model XZE highway tread for rear 1
axle.
1060-0181 RWC AirGuard LED tire pressure monitoring valve stem 1 Manual added by ARIOSECO on 05-
caps (6) for single rear axle applications. Location: Ship SEP-25
loose.
1060-0212 Two Michelin 425 tires model XZE for front axle. 1
BRAKE SYSTEMS
1100-0001 Meritor EX225H 17" disc brakes for front axle. 1
1100-0002 ArvinMeritor 16-1/2'' x 7'' S-cam brakes with cast brake 1
drums for a single rear axle.
1100-0005 Brake system air 4X2/4X4. 1
1100-0006 Parking brake release mounted on the driver's side lower 1
dash.
Page 3 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1100-0020 Compression fittings for all air brake system lines. 1
Includes connections on accessories including air
suspension seats, pump shift, air inlet/outlets and supply
side of plumbing blow-out lines (if equipped).
1100-0024 G4 Electronic Stability Control (4x2), Includes RSC and 1
ATC. Not available on mechanical 4x4, commercial
chassis or tiller. (Available with Ez-Trac 4x4).
AIR SYSTEM OPTIONS
1110-0000-001 Inlet for air system. Location: driver door jamb. 1
1110-0003 Air dryer System Saver 1200. 1
1110-0006 Air lines nylon. 1
1110-0026 Air horns Hadley e-tone recessed in bumper (PR). 1
ENGINES & TRANSMISSIONS
1200-0017 Push-button transmission shift selector. 1
1200-0021 TranSynd, Shell Spirax S6ATF A295, or equivalent 1
synthetic transmission fluid for EVS4000 series.
1200-0097 Electronic limiting of speed to 68 MPH maximum. Note: 1
Axle gear ratio will be as low as possible while allowing
for 68 MPH top speed to improve acceleration. Note:
Max speed may be set at 65 MPH due to tire rating.
1200-0490 Eng/Trans Cummins X10 450HP/1650TQ with EVS4000P 1
transmission. 2027 EPA Compliant. Includes Acumen
telematics and Certified Clean Idle holographic decal.
Note: Until the 2027 EPA engine integration is finalized,
option availability and body design relative to engine and
aftertreatment are subject to change. Additional costs
associated with the 2027 EPA engine will be passed on to
the end user. No exceptions.
1200-0495 Transmission cooler. Required with 2027 EPA 1
engine/trans w/o trans retarder.
SECONDARY BRAKING
1125-0002 Jacobs engine compression brake. Note: Brake lights will 1
illuminate when auxiliary brake is activated.
1125-0023 Transmission to seek second gear when Jacobs engine 1
brake or Telma retarder is engaged. N/A with Trans
retarder.
Page 4 of 36

Salescode Extended Description Qty Prebuild Changes Notes
EXHAUST OPTIONS
1225-0086 Firwin exhaust blanket from the turbo down to the DPF 1
and between the DPF and SCR as needed. Required on
2027 EPA engines.
COOLING PACKAGE
1800-0041 Cooling system for use with Typhoon and Cyclone 1
chassis. For use with 2027 EPA engines. Includes fan
clutch.
FUEL SYSTEMS
1350-0003 Fuel system 50 gallon. 1
1350-0009 Fuel line hose braided. Includes fuel pick-up (if 1
applicable).
1350-0101 Fleetguard fuel/water separator (or equivalent). Shall 1
include indicator light.
ALTERNATOR
1700-0022 Alternator Delco-Remy 430 amp (430 Amp SAE/363 NFPA 1
rating).
BATTERIES
1400-0003 Battery six group 31 1000 CCA. 1 Manual added by ARIOSECO on 05-
SEP-25
CHASSIS OPTIONS
1680-0007 Drivelines 1810. Required on 1550 lb/ft torque or 1
greater engines. N/A with EVS3000 transmission.
1680-0008 Tow eyes front painted below bumper/cab (PR). Tow 1
eyes will be integral when used with a drop style frame
extension.
1680-0011 Tow eyes rear below body, painted. 1
1680-0250-727 Diesel Exhaust Fluid (DEF) 5 gallon tank. Location: inside 1 Manual added by ARIOSECO on 05-
driver side pump module area. SEP-25
1680-0284 Radiator mounted power steering cooler. 1
CAB MODEL
1520-0244 Cyclone long cab - 100" wide (67.5" CA). 1
CAB ROOF TYPE
1615-0005 Delete front vista roof windows. 1
1615-0007 Delete rear vista roof windows. 1
Page 5 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1615-0042 Vista cab roof 4F/16R. Includes 4" front raise and 16" 1
rear raise (12" step up). Windows are provided on the
front of the Vista roof, upper rear doors and upper rear
wall unless otherwise specified. Does not include front
side Vista windows. For use with 100" wide Cyclone only
CAB BADGE PACKAGE
1610-0000 Cab and body to have applicable E-ONE logos. 1
CAB DOOR OPTIONS
1550-0003 Rear crew cab doors in the medium position. 1
1550-0081 Cab door locks - electric. Includes driver side exterior 1
touchpad, (2) remote key fobs, barrel style key lock on
exterior of each door and manual interior lock on each
door.
1550-0083 All cab exterior entry doors to have CH751 keyed locks. 1
1550-0087-000-J7 Red/Fluorescent Yellow Green Diamond Grade chevron 1
"A" stripe on lower cab door panel approx 12" high.
Stainless steel/painted door panels only. E-ONE cabs
only.
1550-0136 Polished stainless steel trim on the vertical edge of the 1 Manual added by ARIOSECO on 05-
over wheel cab compartment opening and/or rear cab SEP-25
compartment (ea).
1550-0185 Cab door panels aluminum painted multi-tone to match 1
cab interior paint. Includes upper and lower panels with
seam below handrail.
1550-0255 Stainless steel protective trim on rear edge of cab door 1 Manual added by ARIOSECO on 05-
jambs on all (4) entry doors. Trim to extend just past the SEP-25
handrails (as applicable). E-One custom chassis only.
1550-0285 Driver and officer door windows to be power actuated 1
with HD regulators. Switches to be located at center
dash. For use with new Typhoon and 100" wide Cyclone
cabs.
1550-0286 Rear crew cab door windows to be power actuated with 1
HD regulators. Switches to be located on each door with
add'l switches accessible by driver. For use with new
Typhoon and 100" wide Cyclone cabs.
Page 6 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1550-0287 Cab doors to be barrier style. For use with new Typhoon 1
and Cyclone only.
1550-0296 Polished stainless steel trim on bottom edge of the 1
exterior cab compartment openings. Includes wheel well
and rear compartments (as applicable).
1550-0377 All cab doors shall have exterior pull style handles with 1
integral key lock (glass reinforced nylon).
CAB STEP OPTIONS
1640-0047 Lower steps to extend 3.5" past cab. For use with legacy 1
Typhoon / Cyclone with barrier style doors and new
Typhoon / Cyclone with barrier style or extended doors.
1640-0067 Cab door bottom step lowered 4" (front and rear doors). 1
Includes extended cab sides / fender trim. For use with
barrier style doors only.
MIRRORS
1670-0021-274 Ramco 8001FFR mirrors. Remote controlled with 1 Manual added by ARIOSECO on 05-
CAS750R top remote convex. Location: mounted on front SEP-25
corners of cab
1670-0031 2" extension for Ramco mirrors. 1
1670-0059 Retrac Mirror stainless steel 10" 3-arm convex above 1
officer side cab brow, 3 piece adjustable telescoping arm.
Head #604953, Arm assy#604671
MISC EXTERIOR CAB OPTIONS
1550-0020 Windows cab side fixed driver's side. 1
1550-0033 Windows cab side fixed officer's side. 1
1675-0022 Pair of 18" handrails located just behind driver and officer 1
front door one each side.
1675-0030 Mud flaps, front, black with E-ONE logo. 1
1675-0046 Rear cab wall to be smooth 3/16" aluminum plate. Cab 1
wall to be finish painted to match the cab paint scheme.
1675-0078 Hansen red LED cab rubber insert handrails upgrade 4
(EA).
1675-0146 Polished stainless steel scuff plates full height on rear cab 1 Manual added by ARIOSECO on 05-
corners (PR). SEP-25
1675-0187 Pair of 24" handrails located just behind driver and officer 1 Manual added by ARIOSECO on 05-
rear door one each side. SEP-25
Page 7 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1675-0201 Large radius cab wheel well. Includes bolt-on adjustable 1
wheel well trim.
1675-0202 Mounting plate for battery charger receptacle, indicator, 1
air inlet, etc (if applicable). Plate to be removable
brushed stainless steel.
1675-0254 Rear cab and vista glass (if so equipped) to have dark 1
tint IPOS. Glass to be smoked glass with 20% light
transmittance (+/- 10%). Includes all glass rearward of
front cab doors.
1675-0455-063 Innovative Controls dual lighted LED folding step. 2 Manual added by ARIOSECO on 05-
Location: officer side back of cab. Each location requires SEP-25
a minimum of (1) handrail per NFPA.
1675-0487 Exterior cab windshield sun visor. Includes integral 1 Manual added by ARIOSECO on 05-
DOT/clearance/marker lights on the leading edge. SEP-25
(Requires 4in roof raise). To be painted as specified.
HVAC
1515-0098 Additional air-conditioner system mounted to the rear 1 Manual added by ARIOSECO on 05-
cab crew area interior headliner. Includes at least four SEP-25
(4) comfort discharge louvers to be used for AC air
delivery. Requires 16" or higher Vista roof.
1515-0133 Air conditioning with roof top mounted condenser. 1
Includes reduced profile evaporator w/powder coated
cover, brushless motors and a rear fan speed switch on
the driver side of the rear air distribution housing.
Requires A/C controls in multiplex display.
SEATS
1510-0007 Seat cover material vinyl. 1
1510-0008 Seat color gray. 1
1510-0135-151 Arm rest installed on both sides of the seat. Location: 1 Manual added by ARIOSECO on 05-
inboard driver's side rear wall. SEP-25
1510-0135-152 Arm rest installed on both sides of the seat. Location: 1 Manual added by ARIOSECO on 05-
inboard officer's side rear wall. SEP-25
1510-0301 Seats, Valor brand. 1
1510-0489 Rear facing USSC Valor ABTS attendant seat officer's 1
side.
1510-0537 Rear wall seats to be mounted approximately 8" apart. 1 Manual added by ARIOSECO on 05-
SEP-25
Page 8 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1510-0590-131 Forward facing rear wall USSC Valor Fortis air ride ABTS 1 Manual added by ARIOSECO on 05-
with R-back. Requires additional S-4 pull-down (1685- SEP-25
0365) if equipped with air bags (one per seat). Location:
driver's side inboard
1510-0590-133 Forward facing rear wall USSC Valor Fortis air ride ABTS 1 Manual added by ARIOSECO on 05-
with R-back. Requires additional S-4 pull-down (1685- SEP-25
0365) if equipped with air bags (one per seat). Location:
officer's side inboard
1510-0627 Driver seat USSC Valor Fortis air ride ABTS. N/A with 1 Manual added by ARIOSECO on 05-
standard flat roof and air bags (S4 raises seat). Note: In SEP-25
Typhoon cabs seat will be 1.5" off center from steering
wheel.
1510-0628 Officer seat USSC Valor Fortis air ride ABTS. N/A with 1 Manual added by ARIOSECO on 05-
standard flat roof and air bags (S4 raises seat). SEP-25
1510-0641 Rear wall seat riser to be approx. 3" in height 1 Manual added by ARIOSECO on 05-
(engineering approval required). SEP-25
1685-0032 Seating capacity tag of five occupants. 1
MEDICAL CABINETS
1535-0202 Finish. Cab medical/storage cabinet(s) finish to be multi- 1
tone gray. Includes interior/exterior of cabinet and
shelves/trays if equipped.
1535-0491 Officer's side rear exterior cab compartment to have 1
entire floor recessed 5".
1535-0575 Driver's side rear exterior cab compartment to have 1
entire floor recessed 5". (N/A
1535-0626 Tray on top of drivers side wheel well cabinet. 1/8" 1 Manual added by ARIOSECO on 05-
aluminum tray size to match top of cabinet with 1 inch lip SEP-25
around the perimeter. Finish to match medical cabinet.
1535-1139 Compartment rear side of cab ''under riser'' type. Approx 1 Manual added by ARIOSECO on 05-
9W x 30H opening. Includes single pan hinged door with SEP-25
(2) push button latches. Long cab with medium door
location only. Location: driver and officer side.
1535-1183 Keyed interior cab compartment door latch with #CH751 1 Manual added by ARIOSECO on 05-
key. Location(s) as specified. SEP-25
Page 9 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1535-1215 Medical cabinet mounted on the wheel well driver side of 1 Manual added by ARIOSECO on 05-
cab with a interior hinged full height door with locking Tri- SEP-25
Mark latch; hinged inboard. Cabinet is 30H x 21W x 24D
on Typhoon and Cyclone and 30H x 24W x 24D on 100"
wide Cyclone. (viewed from interior).
MISC INTERIOR CAB OPTIONS
1685-0005 Lexan sun visors, driver and officer's side overhead. 1
1685-0011 Window Bars for rear cab doors. Stainless Steel. 1
1685-0187 Severe duty engine cover, molded polyurethane. 1
1685-0275-144 Cup holder (PR). Polyurethane construction for use in 2 Manual added by ARIOSECO on 05-
Typhoon and CII with severe duty engine cover only. SEP-25
Location: ship loose.
1685-0446 Severe duty overhead console. Includes driver, center 1
and officer overhead ahead of air conditioning plenum.
Center overhead includes siren mounting locations.
Overhead to match cab interior.
1685-0490 Control lanyard Y type with "Heavy-Duty" (keyring) 1
attachment for air horns. Aircraft style cable (1/8" wire
cable covered with clear plastic/nylon tubing).
1685-0644 HEPA air filtration system for cab interior. Includes 3- 1
speed fan switch on top of enclosure offset forward.
Filter located at rear of engine cover.
1685-0669 Severe duty dash package with low profile center section. 1
Cast alum construction. Includes smooth plate alum
lower kick panels; all painted to match cab interior.
1685-0683 Exterior access cabinets only to not be vented to cab 1 Manual added by ARIOSECO on 05-
interior. For use with, but not limited to, clean cab SEP-25
configurations.
1685-0691 Mechanical fasteners ipos for cab interior. 1 Manual added by ARIOSECO on 05-
SEP-25
1685-0692 Cab insulation package. Includes insulation for ceiling, 1
front wall, rear wall, side walls, below seat risers and in
doors.
1685-0883 Sun visor retainer with rubber (PR). 1 Manual added by ARIOSECO on 05-
SEP-25
1685-0891 Cab interior padding to be gray. 1
CAB ELECTRICAL OPTIONS
Page 10 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1750-0010 Radio speakers additional pair. Locate each side rear cab 1
ceiling.
1750-0024-179-02 Auto-Eject receptacle inlet 20 amp located outside 1
driver's door next to handrail with a Red cover.
1750-0030 Switch horn button two position DOT/electronic siren. 1
1750-0046-195 Cab Headlights. Position: lower. 1
1750-0073-3UU Antenna base Tessco P/N 90942 (NMO Motorola Style - 3 Manual added by JKOOGLER on 21-
also called MATM style) on cab roof. Location: per AUG-25
antenna layout drawing with coaxial cable terminating
behind the officer seat.
1750-0166 ATC override switch. 1
1750-0198-762 Battery charger to be located behind officer's seat. 1
1750-0198-K60 Battery charger to be located L1 backwall offset forward 1 Manual added by JKOOGLER on 21-
up high. AUG-25
1750-0214-3XY Mount customer supplied GPS antenna on cab roof. 1 Manual added by JKOOGLER on 21-
Location: per antenna layout drawing with cable AUG-25
terminating center of dash.
1750-0265 Speedometer for officer side multiplex display. 1
1750-0449 Momentary DPF regeneration override switch. 1
1750-0554 FireTech LED cab headlights. 1
1750-0580 Light EON LED (EA) mounted in riser height 2
compartment.
1750-0768 TecNiq D07 LED cab door step area lighting. Includes (2) 1
lights at each door area. Lights to be switched with door
ajar.
1750-0796 Turn signal TecNiq LED strip (PR) with clear lens and 1
polished alum housing located between quad headlight
bezels (New Typhoon and Cyclone only).
1750-0815-847 Radio Aptiv model PP105221 heavy duty 1
AM/FM/Weatherband with Bluetooth, aux input, and USB
port. Located center overhead console offset to officer
side. Includes speakers adjacent to driver and officer
seats and remote Bluetooth microphone P6604240.
Page 11 of 36

Salescode Extended Description Qty Prebuild Changes Notes
1750-0952 Customer supplied cable. Route customer supplied cable 1 Manual added by JKOOGLER on 21-
(must be new cable, used cables will not be accepted) AUG-25
leaving a service loop at each end. Terminating
locations, cable type, and service loop size to be as
specified by Sales. Quantity is per cable to be installed.
1750-1003 Battery charger Kussmaul Chief Series. 120/240 volt inlet, 1
40 amp output. Includes built-in touch screen display.
1750-1007-179-02 A Red Super Auto Eject Deluxe Cover with OLED display, 1
for the auto eject located outside driver's door next to
handrail. 20A receptacles only. Kussmaul Chief chargers
only without external display(1750-1003). Option shall be
in place of auto eject standard cover.
1750-1013-545 Dual port USB charging receptacle in the cab wired 1
battery hot. Includes USB-A and USB-C ports. Location:
In cab driver side on 3 x 3 post rear facing just above
engine cover (or seat riser if in a Hush).
1750-1013-546 Dual port USB charging receptacle in the cab wired 1
battery hot. Includes USB-A and USB-C ports. Location:
In cab officer side on 3 x 3 post rear facing just above
engine cover (or seat riser if in a Hush).
1750-1013-593 Dual port USB charging receptacle in the cab wired 2
battery hot. Includes USB-A and USB-C ports. Location:
officer side dash.
1750-1013-747 Dual port USB charging receptacle in the cab wired 1
battery hot. Includes USB-A and USB-C ports. Location:
driver side rear cab wall in or below seat support
structure as space allows.
1750-1013-748 Dual port USB charging receptacle in the cab wired 2
battery hot. Includes USB-A and USB-C ports. Location:
officer side rear cab wall in or below seat support
structure as space allows.
1750-1016 Digital dash display for driver. 1
5400-0057 Dome lts red/white 4" LED (4). Lights to be located two 1
front and two rear. White light wired through door and
light assembly mounted rocker switch. Red light through
light assembly mounted rocker switch.
Page 12 of 36

Salescode Extended Description Qty Prebuild Changes Notes
BODY COMPT LEFT SIDE
3100-0139 Compartment L1 to have rescue style interior 1 Manual added by VHAYDEN on 10-
compartment depth and height. SEP-25
3100-0941 Driver side body with full height 32" wide forward and 1 Manual added by VHAYDEN on 10-
50" wide rearward compartmentation. Includes (1) 56" SEP-25
wide compartment over the wheel well.
BODY COMPT RIGHT SIDE
3120-1222 Officer side body with full height 32" wide forward and 1 Manual added by VHAYDEN on 10-
50" wide rearward compartmentation. Includes (1) 56" SEP-25
wide compartment over the wheel well.
3365-0079 2-arm ladder rack on officer side. The ladder rack 1
includes amber lights on each end to visually indicate
when the rack is in motion. Restricts the top folding step
(if optioned) from closing completely. Includes mounting
bracket (if required, matching rear compartment face or
compartment wrap finish) for components mounted on
rear compartment face
BODY COMPT REAR
3110-0044 Bolt-on diamond plate 10" tailboard (full width of body). 1 Manual added by VHAYDEN on 09-
Includes handrails- (2) mounted vertical on trailing edge SEP-25
of body and horizontal mounted handrail(s) below
hosebed.
3110-0596 Single low rear compartment. For use with low hosebed. 1 Manual added by VHAYDEN on 09-
Includes smooth plate panels. This compartment shall be SEP-25
transverse through to the left rear side
DOORS
3300-0007-003 Door single vertical hinged painted. Location(s): L1 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0007-015 Door single vertical hinged painted. Location(s): R1 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0141-003 Tri-Mark door latch. Location(s): L1. 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0141-004 Tri-Mark door latch. Location(s): L2. 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0141-005 Tri-Mark door latch. Location(s): L3. 1 Manual added by VHAYDEN on 09-
SEP-25
Page 13 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3300-0141-015 Tri-Mark door latch. Location(s): R1. 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0141-016 Tri-Mark door latch. Location(s): R2. 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0141-017 Tri-Mark door latch. Location(s): R3. 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0141-027 Tri-Mark door latch. Location(s): B1. 1 Manual added by VHAYDEN on 09-
SEP-25
3300-0220-003 Reverse hinge single compartment door. Includes vertical 1 Manual added by VHAYDEN on 09-
mounted drip rail along forward area of compartment SEP-25
opening (in addition to the horizontal drip rail above the
door opening). Location(s): L1.
3300-0289-004 Door double vertical hinged w/rotary latches - painted . 1
Location(s): L2 Includes latch handle extension installed
on secondary door's interior latch with "PULL" tags using
.125 plate.
3300-0289-016 Door double vertical hinged w/rotary latches - painted . 1
Location(s): R2 Includes latch handle extension installed
on secondary door's interior latch with "PULL" tags using
.125 plate.
3300-0290-027 Door double vertical hinged w/rotary latches - smooth 1 Manual added by VHAYDEN on 09-
plate sanded. Location(s): B1. Includes latch handle SEP-25
extension installed on secondary door's interior latch with
"PULL" tags using .125 plate.
3300-0292-005 Door double 3-point vertical hinged w/rotary latches - 1
painted. Location(s): L3. Includes latch handle extension
installed on secondary door's interior latch with "PULL"
tags using .125 plate.
3300-0292-017 Door double 3-point vertical hinged w/rotary latches - 1
painted. Location(s): R3. Includes latch handle extension
installed on secondary door's interior latch with "PULL"
tags using .125 plate.
SHELVES
Page 14 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3370-0245 Permanent fixed shelf. Aluminum or stainless steel body 2 (1) L3 inverted for tool board.
applications. Location: (1)R3 from the top of the partition
to the rear of the unit. Customer
installed Medi Redi to fit under the
shelf and rearward of partition
3370-0246 Adjustable shelf for non-transverse compartments. 9 (2) L1; L3 (1) Lower; (2) R1 One
Location: Mid Height and One upper; R3 (4)
two full size up high and two
forward of the partition
3370-0247 Tracks for adjustable shelf and/or adjustable tray in a 5 L1; L3; R1; R2; R3 forward of
compartment. Location: partition and high above partition
3370-0336-005 Adjustable shelf for non-transverse compartments. 1 Manual added by VHAYDEN on 09-
Includes inverted front lip and shelf mounted at an angle SEP-25
with edge at door opening 5 inches lower than rear.
Location: L3.
COMPARTMENT DIVIDERS
3390-0557 Partition, bolt-in vertical partition wall. Location: 1 R3 to be 38 inches high and 17
inches off the back cover of the
ladder rack swivel
TRAYS / TOOLBOARDS
3380-0498 Tray, floor mounted roll-out with gas spring. 500 lbs. 1 R1;
capacity. Location:
3380-0626 Vertical hinged heavy duty swing-out pegboard 1 L3 upper 19.5 inches high hinged
toolboard. Hinge along forward compartment wall (unless forward
otherwise stated in location) and position centered
between door and back wall. Includes latch to secure in
the closed position that is accessible from the ground.
Location:
COVERS
3305-0219 (2) piece light weight aluminum hose bed cover. Includes 1 Manual added by VHAYDEN on 10-
center hose bed divider with notched rear (as SEP-25
applicable), fill tower(s) access door(s) and handles (as
applicable), gas shocks, positive hold opens/hold closed
at rear, (2) grab handles front and (2) hand rails rear.
NOTE: Hosebed/Cover length cannot exceed 150 inches.
Page 15 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3305-0278 The center divider/support for the hosebed cover shall be 1 Manual added by VHAYDEN on 10-
offset. Add note to specify exact requirement. SEP-25
3305-0430 Nylon black cargo net pull strap(s) and stainless steel 1 Manual added by VHAYDEN on 09-
quick release buckle(s) on each side for crosslay cover. SEP-25
Includes 2" stainless steel quick release buckle(s)
(female end) to be attached at top of the module with
the male portion attached to the cargo net. Footman
loops to be on the bottom of the cargo net. Orange 1"
nylon pull strap to be attached to the paddle to release
for quick drop down access. Note pull straps to be
attached to the crosslay with approx 5" hand loop at end
and velcro on the back to hold in place during travel.
3305-0518 Nylon black cargo net crosslay cover. Side flaps are 1 Manual added by VHAYDEN on 09-
selected separately. SEP-25
3305-0719 Hosebed cover not to include notch around hosebed 1 Manual added by VHAYDEN on 09-
storage box. Cover will go over storage access. SEP-25
3305-0855 (2) Two piece nylon black cargo net at rear of diamond 1 Manual added by VHAYDEN on 09-
plate or vinyl hose bed SEP-25
PUMP MODULE
3130-0167 Pump module to be 76" wide (side to side). Includes 1
upper, lower, crosswalk, speedlay and tranverse
module(s) if applicable.
3130-0523 Side mount pump module. Extruded aluminum with 1
runningboards.
3130-0534 Pump panel opening is 51" wide. 1 Manual added by GFRANKLIN on
09-SEP-25
3130-0540 Pump module height is 80". Pumper / tanker only. 1
PUMP PANELS
3134-0016 Stainless steel driver and officer side pump panels. 1
3134-0082 Driver side pump panel Escutcheon Plate shall be hinge 1 Manual added by GFRANKLIN on
forward. Include thumb Latches. 09-SEP-25
3134-0143 Officer side pump panel to be vertical hinged on forward 1
extrusion. Panel to be (3) pieces with upper (2) panels
secured in the closed position with push button latches.
Upper panel to be held open with gas shock.
MISC PUMP PANEL OPTIONS
Page 16 of 36

Salescode Extended Description Qty Prebuild Changes Notes
4460-0003 Pump panel tags color coded per NFPA compliance. 1
4460-0009 Pump panel tags, special color. (Must specify.) 1 TBD
4460-0010 Pump panel tags - Special label. (Must specify.) 1 TBD
4460-0133 Foam label mounted on fill tower lid " F500 ONLY" . 1 Manual added by GFRANKLIN on
09-SEP-25
PUMP MODULE OPTIONS
3136-0048 Notched crosslay divider(s) on both ends for preconnect 1
line(s) nozzle end storage with NFPA cover(s) in closed
position.
3136-0058 E-ONE logo mounted one each side on pump 1
module/preconnect panels or at upper body section as
shown on approval drawing. Logos to be sized as
applicable to available space on panels.
3136-0074 Stainless steel scuff plates for crosslays and/or 1 Manual added by VHAYDEN on 09-
speedlays. SEP-25
3136-0138 Pump module storage pan. 1
3136-0418 Crosslay triple 5"/5"/5" wide single stack to hold up to 1 Manual added by VHAYDEN on 09-
150' to 200' of 2.5" DJ hose each. SEP-25
WATER TANK
4010-0064 780 Gallon" L" shape Water Tank. Includes lowered rear 1 Manual added by VHAYDEN on 10-
section for lower hosebed height. Note: Any foam cell(s) SEP-25
optioned will reduce the overall water
4010-0223 Fill tower(s) to be located offset to driver side of water 1 Manual added by VHAYDEN on 09-
tank. SEP-25
4010-0511 Water tank and foam cell(s) (if applicable) shall be UPF 1
(United Plastic Fabricating) brand.
TANK PLUMBING
4450-0011 2.5" tank fill Akron manual valve. At pump panel. 1
4450-0119 3" tank to pump Akron manual valve w/4" tank 1
connection.
4450-0207 2" Tank to Pump Electric Over Air Actuated Valve. 1 Manual added by GFRANKLIN on
09-SEP-25
FOAM TANK
4100-0009-590 30 gallon integral foam tank for Class A foam. Foam tank 1
capacity will reduce the water tank capacity. Tank
capacity is 30 US gallon / 25 Imperial gallons / 113
Liters.
Page 17 of 36

Salescode Extended Description Qty Prebuild Changes Notes
LADDER STORAGE / RACKS
3365-0025-516 Attic ladder mounting brackets (PR). Locate inboard side 1
of ladder rack.
3365-0049 Brand of ladders capable of being carried on unit to be 1
Alco-Lite.
3365-0081 2-Arm Ladder Rack to be painted job color. 1
3365-0082-122 Hydraulic Power Supply for E-ONE 2-Arm Ladder Rack. 1
Location: dunnage pan offset to officer side.
3365-0087-0G8 The length of ladders capable of being stored shall be 1 Manual added by VHAYDEN on 10-
the following: 24' 2-section, 16' roof ladder and 10' attic SEP-25
ladder w/shoes.
3365-0128-48Q Pike pole storage tube (1) One. Locate hosebed storage 1 Manual added by VHAYDEN on 09-
compartment. SEP-25
3365-0568 Top of the storage area shall have hosebed style slats to 1 Manual added by VHAYDEN on 09-
prevent accumulation of water and allow for ventilation SEP-25
of wet hose.
3365-0845-2F8 Storage in the hosebed with open top and sanded 1 Manual added by VHAYDEN on 09-
smooth plate door with thumb latch(s). Includes SEP-25
composite flooring if applicable for easy removal and
loading of the contents and stop(s) as required to
prevent the contents from sliding forward. Option
Includes 1 divider. If equipped with a door, it is to be
wired to the "Door Open" indicator inside cab
3365-1375 (1) D-handle pike pole storage box. Locate in hosebed 2 Manual added by VHAYDEN on 09-
storage. SEP-25
3365-1376 Hosebed storage area capable of holding: (1)6' CWH 1 Manual added by VHAYDEN on 09-
ceiling hook with D handle & (1)8' CWH ceiling hook with SEP-25
D handle, (1) 8' RH ventilation/trash hook (1) 18" x 2" x
72" backboard. See sales drawing for location.
3365-1390 Upper hosebed storage area above officer side 1 Manual added by NGRIFFIN on 19-
compartments as applicable. Upper storage area to have MAR-26
an open top and run length of the hosebed area.
3365-1424 Controls for the ladder rack shall be recessed on the rear 1 Manual added by VHAYDEN on 09-
face of the body, officer side. The control box shall have SEP-25
a hinged door for easy access of ladder rack controls and
operation.
HANDRAILS / STEPS
Page 18 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3330-0001 Slide-out platform, integral driver side running board 1 Manual added by VHAYDEN on 09-
(includes hand rail as applicable). SEP-25
3330-0008-1XD Handrail up to 12". Location: driver side front of pump 1 Manual added by VHAYDEN on 09-
module. SEP-25
3330-0008-1XE Handrail up to 12". Location: officer side front of pump 1 Manual added by VHAYDEN on 09-
module. SEP-25
3330-0023 Slideout platform-integral officer side running board. Not 1 Manual added by VHAYDEN on 09-
available with a front suction (includes handrail as SEP-25
applicable).
3330-0072 Hansen red LED body rubber insert handrails upgrade 1
package (includes pump module if applicable).
3330-0277 Innovative Controls dual lighted LED folding steps rear 1
NFPA. Includes folding steps on driver side rear of the
body. (staggered stepped as applicable with tailboard
depth) for NFPA hosebed access and handrail mounted
on driver side upper hosebed side (as applicable).
3330-0279-062 Innovative Controls dual lighted LED folding step. 4
Location: driver side front compartment face. Each
location requires a minimum of (1) handrail per NFPA.
3330-0279-501 Innovative Controls dual lighted LED folding step. 1 Manual added by VHAYDEN on 09-
Location: driver side rear of body. Each location requires SEP-25
a minimum of (1) handrail per NFPA.
3330-0394 Intermediate pump panel step officer side with rearward 1 Manual added by VHAYDEN on 09-
tapered corner. Includes step lighting (as applicable). SEP-25
Step light to be switched thru work light in cab. Includes
hand hold cut-outs on top of the step.
3330-0546 Step rear 8" intermediate embossed treadplate. Locate 1 Manual added by VHAYDEN on 09-
below hosebed, includes three (3) hand hold cut-outs on SEP-25
top of the step in place of the hand rail.
MISC BODY OPTIONS
3340-0004 Hosebed above the booster tank. Includes forward 1
hosebed and tower(s) cover plate work (as applicable).
Hosebed adjustable divider extrusion in the forward area
and rearward area of the hose bed to run full width of
the hosebed (as is practical with other hosebed mounted
equipment)
3340-0035 Divider Long. To run full length of hose bed (front to 1 Manual qty change by VHAYDEN
rear). on 10-SEP-25
Page 19 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3340-0058 Recessed fuel fill driver side wheel well. 1
3340-0074 Body mainframe and hosebed side assemblies for a 85" 1
high body.
3340-0089-000-13 Turtle Tile Brand Black Floor Matting covering all 1
applicable Compartment Floors, Shelves, and Rollout
Trays. Does not include roof top compartments (Added
3340-0093 Mud flaps, rear, black with E-ONE logo. 1
3340-0102 (Boston style) Angled tailboard corners. 1 Manual added by VHAYDEN on 09-
SEP-25
3340-0110 The rear of each hose bed divider to have a hand hold 1
cut-out(s).
3340-0145 Rub rail for the body and pump area module(s) (as 1
applicable).
3340-0191 Divider Support to run full width of hosebed (side to side) 1 Manual added by VHAYDEN on 09-
at the front of the hosebed and towards the rear of the SEP-25
hosebed at top of the divider(s). Attach to each hosebed
divider to provide additional support.
3340-0302 Long hose bed divider(s) to be held short to allow for 1
adjustability of the divider(s) with hose bed
preconnect(s) if applicable per hose loading and option
locations.
3340-0486 Diamond plate single axle wheel well. Includes bolt-on 1
composite wheel well liners and bolt-on polished alum
fenderette.
3340-0681 Body mainframe layout line to be 24". Includes body and 1
all applicable modules.
3340-0699 Bolt-on cover plate over upper section of water tank to 1 Manual added by VHAYDEN on 10-
be embossed diamond plate. SEP-25
3340-0961 Divider long fixed at the edge of the step-down in 1 Manual added by VHAYDEN on 10-
hosebed (officer side). Divider to run full length of hose SEP-25
bed (front to rear).
3340-1648 Anodized aluminum trim on bottom edge of all body 1
compartment openings including pump enclosure if
applicable with painted edges.
Page 20 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3340-2761 Raise floor in right side compartment(s) as required to 1
clear engine after-treatment system. Door opening(s) to
remain standard height. This modification affects
compartment dimensions in specs. See sales drawing for
updated dimensions.
3340-2768-966 Pair of cast Wheel chocks (folding) for use up to 44" 1 Manual added by VHAYDEN on 09-
diameter tires, with mounting brackets located to be SEP-25
mounted at final inspection.
SCBA BOTTLE STORAGE
3320-0100 Strap, loop style to retain SCBA bottle(s). Locate one per 1
bottle in each exterior body storage compartment.
3320-0182-497 E-ONE designed (1) SCBA bottle storage driver side body 1
wheel well offset rearward with hinged door and push
button latch. Door material to match wheel well material.
Holds standard size SCBA bottle, 20lbs ABC Extinguisher
(10.25"x7"x24") or 2.5 gal Water Extinguisher
(9"x7"x24.5"). Door shall cover the recessed fuel fill if
located in the wheel well adjacent to the SCBA storage.
3320-0184-498 E-ONE designed (3) SCBA bottle storage officer side body 1
wheel well offset forward with hinged door and push
button latch. Door material to match wheel
3320-0184-500 E-ONE designed (3) SCBA bottle storage officer side body 1
wheel well offset rearward with hinged door and push
button latch. Door material to match wheel well material.
Holds standard size SCBA bottles. Upper storage troughs
hold standard size 20lbs ABC Extinguisher
(10.25"x7"x24") or 2.5 gal Water Extinguisher
(9"x7"x24 5") in each trough
3320-0399-495 E-ONE wheelwell eqipment storage compartment driver 1 Manual added by VHAYDEN on 09-
side body wheel well offset forward with hinged door and SEP-25
push button latch. Door material to match wheel well
material and be wired to door ajar. Includes a slide out
bin (sanded finish) without lips and door on top and grab
handle on front
HRT SYSTEMS
Page 21 of 36

Salescode Extended Description Qty Prebuild Changes Notes
3325-0036-121 Harrison Hydra-Qube Jr. Location: dunnage pan offset to 1 Manual added by GFRANKLIN on
driver side. Requires PTO or drive-through hyd pump. 09-SEP-25
PUMPS
4005-0031 Rating 1500 GPM. 1
4005-0190 Darley 1.5 AGH single stage hydraulically driven 1 Manual added by GFRANKLIN on
centrifugal pump. 09-SEP-25
4005-0201 Waterous CSU 1500-2250 GPM single stage pump. 1
Requires primer option.
PUMP CERTIFICATION
4475-0000 Pump certification 750-2250 GPM (or metric/imperial 1
equivalent).
PUMP OPTIONS
4015-0012 Pump shift override, side panel mounted. 1
4015-0044 Anodes for Waterous pump - (Pair) (1) discharge side 1
and (1) intake side.
4015-0053-198 Steamers to be Flush + 1". Location: driver's side. 1
4015-0053-199 Steamers to be Flush + 1". Location: officer's side. 1
4015-0091 Pump cooler with .75" 1/4 turn valve. 1 Manual added by GFRANKLIN on
09-SEP-25
4015-0098 Manual operated master pump drain. The master drain 1
shall be clearly marked and placed in accessible location
on pump panel.
4015-0165 Pump seal mechanical for Waterous pump. 1
4015-0167 Pump&Roll pump automatic cooler to cool the pump for 1 Manual added by GFRANKLIN on
periods of pumping when water is not being discharge. 09-SEP-25
4015-0242 Trident primer W/3 barrel push button control. For use 1
with 1250 GPM and larger
4015-0364 PTO Pump/Midship Pump plumbing shall be manifold 1 Manual added by GFRANKLIN on
together with check valves for for the booster reel only. 05-MAR-26
4015-0384 2-Button electric pump shift. 1
4015-0391 Pump&Roll Preset hydraulic flow control valve. Hydraulic 1 Manual added by GFRANKLIN on
flow control valves to be preset so water pump will 09-SEP-25
maintain 125PSI.
INTAKES
4440-0005 2.5" Left Intake Akron Manual Valve. 1
Page 22 of 36

Salescode Extended Description Qty Prebuild Changes Notes
4440-0006 2.5" Right intake Akron manual valve. 1
INTAKE OPTIONS
4445-0009 Intake relief valve, Akron. 1
4445-0134 Left/Right Aux Intake shall be extended out 1 Manual added by GFRANKLIN on
approximately 4" from standard location to rear. 09-SEP-25
DISCHARGES AND PRECONNECTS
4415-0008 1.5" Front bumper discharge Akron manual valve. 1
4415-0012-654 1.5" Crosslay with Akron manual valve. Location: crosslay 2
1 & 2.
4415-0016-1PY 2.5" Right Pump Panel Discharge Akron Manual Valve. 1 Manual added by GFRANKLIN on
Location: right side discharge 5. 09-SEP-25
4415-0016-584 2.5" Right Pump Panel Discharge Akron Manual Valve. 1
Location: right side discharge 2.
4415-0016-675 2.5" Right Pump Panel Discharge Akron Manual Valve. 1
Location: right side discharge 3.
4415-0016-B53 2.5" Right Pump Panel Discharge Akron Manual Valve. 1 Manual added by GFRANKLIN on
Location: right side discharge 4. 09-SEP-25
4415-0041 3" Deck Gun Discharge, Akron manual valve. (outlet shall 1
terminate with MNPT threads unless extend gun is
install)
4415-0054-583 4" Right Pump Panel Discharge with 3" Akron Manual 1
Valve (Waterous pumps noted location to be forward
lower port). Location: right side discharge 1.
4415-0058-655 2.5" Crosslay Akron Manual Valve. Location: crosslay 3. 1
4415-0067 1.5" left front hose bed preconnect Akron manual valve. 1
4415-0178-530 Polished Stainless Steel Swivel Located on Top of Bumper 1
driver's side outboard for Front Bumper Discharge.
4417-0106-123 Deck gun piping to be positioned dunnage pan centered. 1 Manual added by GFRANKLIN on
09-SEP-25
DISCHARGE OPTIONS
4417-0034 Deck gun TFT 18" Extend-A-Gun, 3" manual 1
operation.(outlet shall terminate with MNPT threads)
4417-0175 Innovative Controls push/pull valve controls with locking 1
T handles.
Page 23 of 36

Salescode Extended Description Qty Prebuild Changes Notes
4417-0176 Innovative Controls 3/4" bleeder/drain valve include lift 9
lever with ergonomic grip.
4417-0185 Innovative Controls discharge and intake bezels with 1
integral color code and verbiage for side mount pump
panel.
4417-0244 Ferrell Compression Fittings to be use on all plumbing 1 Manual added by GFRANKLIN on
plastic tubing. 09-SEP-25
4417-0349 TM/SM Valve controls to be Innovative Controls Pistol 13 Manual added by GFRANKLIN on
Grip-handles with cable actuators. 09-SEP-25
4417-0451 Elkhart 8297 Manual Stinger Monitor with Stream Shaper, 1 Manual added by GFRANKLIN on
SM-1250 NOZZLE, LDH/5" Storz Inlet Base and truck 09-SEP-25
mount adapter to attach to deck gun discharge.
BOOSTER REEL
4405-0090-027 Booster Reel with air actuated control at pump operator 1 Manual added by GFRANKLIN on
panel. Shall hold 200' of 1" Booster Hose (Hose not 11-SEP-25
included) installed in B1
4405-0116 Remove Hose reel blow-out. 1 Manual added by GFRANKLIN on
09-SEP-25
4405-0191 Booster reel hose in loose equipment shall be install on 1 Manual added by GFRANKLIN on
reel. 09-SEP-25
PRESSURE GOVERNORS
4465-0047 FRC PumpBoss Max pressure governor (PBA500 series). 1
Includes engine monitor gauges.
GAUGES
4435-0031 Pump hourmeter on pump operator's panel. 1
4435-0286 Fire Research TankVision Pro model WL360-A00 Class A 1
foam tank level gauge.
4435-0313-Y09 FRC TankVisionWLA300-A00/FRC Maxvision water tank 1 Manual added by GFRANKLIN on
level gauge package. Location of FRC Maxvision tank 09-SEP-25
level lights: each side of cab behind rear cab doors up
high.
4435-0451 Innovative Controls TC Series 2.5" (63MM) pressure 9
gauge with chrome bezel.
4435-0453 Innovative Controls TC Series 4" (100MM) Master 1
pressure gauges with dual chrome bezel. Includes
integrated test ports and alarm.
4435-0458 Pump panel pressure gauges to be 0-400 / Master Intake 1
gauge if applicable to be 30-0-400.
Page 24 of 36

Salescode Extended Description Qty Prebuild Changes Notes
FOAM SYSTEMS
4430-0047-556 125 GPM Akron foam eductor. Location: 1.5 first 1
crosslay.
4430-0079 The foam system performance shall be tested and 1
certified in compliance with the applicable NFPA
requirements.
FOAM SYSTEM OPTIONS
4432-0054-556 Akron Quick Disconnect Foam Pickup Tube on Driver's 1
Side Pump Panel for Eductor. Located on: 1.5 first
crosslay.
4432-0056-282 Hale EZ-Fill foam system for a single foam tank. Includes 1
clear hose wand (shipped loose). Controller and
connection port located driver's side pump panel.
4432-0211 All foam service/drain valves to be brass, or stainless 1 Manual added by GFRANKLIN on
steel IPOS. No PVC valves to be used. 09-SEP-25
ELECTRICAL SYSTEMS
5010-0049 Vehicle data recorder - 2009 / 2016 / 2024 NFPA 1
compliant. Includes occupant detection shown in
multiplex display. E-ONE chassis only.
5010-0081 Pump and roll screen for multiplex display. Reference 1 Manual added by GFRANKLIN on
specification for details. 09-SEP-25
5010-0094 Nanoprotech (or equivalent) corrosion inhibiting spray 1
coating to be applied on all exposed electrical
connections.
5010-0145 HVAC Controlled through multiplex display(s). 1
5010-0153 ControlMaxx Electrical system for pumper / tanker / 1
rescue / ARFF.
5010-0158-168 10" display for multiplex electrical system. Location: 1
officer's side engine cover.
5010-0158-649 10" display for multiplex electrical system. Location: 1
driver's side engine cover.
LIGHT BARS
5300-0504 Whelen MKEZ7 1.5" standard mount for front light bar 1
(PR).
5300-0506-000-7W Front light bar LED color: As Specified (If applicable, 1 Manual added by JKOOGLER on 21-
includes side facing when colors are the same.) AUG-25
Page 25 of 36

Salescode Extended Description Qty Prebuild Changes Notes
5300-0507 Light bar Whelen Freedom IV Model F4X7 72" with 14 1
LED modules. Location: Centered on the front cab roof.
WARNING LIGHTS
5600-0787-3RH-4T Warning light Whelen M2W Wide Angle Super LED (PR). 1
Surface mounted w/chrome flanges (if applicable).
Location: (1) each side NFPA/ULC required lower zone
rear side facing, color will be RED with CLEAR lenses.
5600-0801-G99-4T (Obsolete: Use Sales Code 5600-1044) Light Whelen 1 Manual added by JKOOGLER on 21-
Strip-Lite Plus Surface Mount RED with CLEAR lenses AUG-25
Super-LED Series (PR). Only available with clear lens.
Location: (1) each side of body side facing upper
rearward.
5600-0815-457-O6 Warning light Whelen M92 DUO series Super LED (PR) 1 Manual added by JKOOGLER on 21-
RED/AMBER. Location: (1) each side of body rear facing AUG-25
up high.
5600-0815-806-78 Warning light Whelen M92 DUO series Super LED (PR) 1 Manual added by JKOOGLER on 21-
Red/Blue. Location: (1) each side of cab, rearward of AUG-25
rearward doors, up high.
5600-0850-170 Hazard (door ajar) light TecNiq S38 LED red. Location: 1
center overhead.
5600-0948-3RF-4T Warning light Whelen M6 series Linear Super LED (PR) 1
RED with CLEAR lenses. Location: (1) each side
NFPA/ULC required lower zone forward side facing.
5600-0948-3RG-4T Warning light Whelen M6 series Linear Super LED (PR) 1
RED with CLEAR lenses. Location: (1) each side
NFPA/ULC required lower zone midship side facing.
5600-0948-463-12 Warning light Whelen M6 series Linear Super LED (PR) 1 Manual added by JKOOGLER on 21-
White. Location: (1) each side in front quad inboard of AUG-25
NFPA warning light.
5600-0948-464-4T Warning light Whelen M6 series Linear Super LED (PR) 1
RED with CLEAR lenses. Location: (1) each side of cab
down low just ahead of rear doors.
5600-0957 Sensor, photocell Whelen LCPHOTO. For use with 1 Manual added by JKOOGLER on 21-
Whelen DVI / Low Power enabled lights only. See spec AUG-25
for lighting compatibility.
Page 26 of 36

Salescode Extended Description Qty Prebuild Changes Notes
5600-0990-3RE-78 Warning light Whelen M6 DUO series Linear Super LED 1 Manual added by JKOOGLER on 21-
(PR) Red/Blue. Location: (1) each side NFPA/ULC AUG-25
required lower zone front facing. M6 DUO lights are only
available with clear lenses and in the following color
combinations: Red/Blue, Red/White, Blue/White,
Amber/Blue Red/Amber or Amber/White
5600-0990-3RI-78 Warning light Whelen M6 DUO series Linear Super LED 1 Manual added by JKOOGLER on 21-
(PR) Red/Blue. Location: (1) each side NFPA/ULC AUG-25
required lower zone rear facing. M6 DUO lights are only
available with clear lenses and in the following color
combinations: Red/Blue, Red/White, Blue/White,
Amber/Blue Red/Amber or Amber/White
DIRECTIONAL LIGHT BARS
5310-0017 Whelen Traffic Advisor model TAL65 LED - 36" long. 1
5310-0020-170 Directional light bar control is to be located center 1
overhead.
SIRENS
5500-0011-211 Federal Q2B siren - Pedestal mounted on bumper. 1
Location: officer side front bumper. Requires activation
switch.
5500-0015 Whelen model 295SLSA1 siren with microphone 1
(replaced 295HFSA1).
5500-0024-171 The primary electronic siren control is to be located 1 Manual added by JKOOGLER on 21-
driver's overhead. AUG-25
SPEAKERS
5510-0029-852 Speaker, Federal Signal Dynamax ES100 with "E-ONE" 2
grille through bumper. Location: one each side front
bumper inboard of frame.
DOT LIGHTING
5150-0017 License plate light LED with chrome housing located at 1
the rear of the body.
5150-0080-461 Weldon auxiliary turn signal model 9186-8580 LED (PR). 1
Location: (1) each side in body wheel well offset forward.
5150-0151 Marker light package cab / body LED. Body lights to be 1
.75" Dia for custom pumpers and tankers.
5150-0271 Bracket license plate at rear of body. Smooth plate 1
sanded bracket.
Page 27 of 36

Salescode Extended Description Qty Prebuild Changes Notes
5150-0299-5WD Front (if applicable) and rear turn signal flash pattern: 1
sequential arrow.
5150-0302 Whelen M6 series LED vertical mount tail lights. Includes 1
LED stop/tail, turn and back-up lights with vertical 4 light
housing and weatherproof connectors. Requires turn
signal flash pattern.
LIGHTS - COMPARTMENT, STEP & GROUND
5380-0280 Ground light package TecNiq T440 4" LED - large. 1
5380-0473 Compartment light package TecNiq E45 LED for medium 1
bodies. Includes two lights per compartment (four if
transverse).
5380-0476 Compartment light TecNiq E45 LED for medical cabinet 1
(EA).
LIGHTS - DECK AND SCENE
5390-0264-490 FireTech FT-GESM scene lights (PR) with chrome flange 1
(when required) and weatherproof connectors. Switch in
cab (driver and officer side lights switched separately).
Locate: (1) each side of vista forward of rear doors.
5390-0277-490 Fabricated recess mounting box for hosebed, deck, 2 Manual added by JKOOGLER on 21-
scene, flood or work light (EA). Location: (1) each side of AUG-25
vista forward of rear doors.
5390-0290-4VK Hosebed strip light FireTech model FT-CU-HD-12-B LED. 1 Manual added by JKOOGLER on 21-
Locate: (3) on each section of hosebed cover evenly AUG-25
spaced (as required). Switched with work light switch in
cab.
5390-0291-0VA Crosslay strip light FireTech model FT-CU-HD-12-B LED. 1 Manual added by JKOOGLER on 21-
Locate: center back of cab up high for crosslay lighting. AUG-25
Switched with work light switch in cab.
5390-0291-K69 Crosslay strip light FireTech model FT-CU-HD-12-B LED. 1 Manual added by JKOOGLER on 21-
Locate: (1) each side back of cab for crosslay lighting. AUG-25
Switched with work light switch in cab.
5390-0334-457 FireTech FT-GSMJR scene lights (PR) with chrome flange 1 Manual added by JKOOGLER on 21-
and weatherproof connectors. Switch in cab (driver and AUG-25
officer side lights switched separately). Locate: (1) each
side of body rear facing up high.
LIGHTS - NON-WARNING
Page 28 of 36

Salescode Extended Description Qty Prebuild Changes Notes
5400-0008 (1) pump panel light over the pump control area to be 1
wired to come on when pump shift is placed in pump.
(Side mount forward light noted, Top Mount is center
light.)
5400-0222 Pump compartment light Optronics ILL22 Series LED 1
(EA). Includes separate on/off switch inside pump access
door / panel. Light circuit to be wired through battery
switch.
5400-0224 Engine compartment light Optronics LED Series ILL22 1
(EA).
5400-0259 TecNiq model E10 pump panel LED light package with 1
(3) lights per side pump panel. Pump panels over 45"
may require additional lights. Side mount only.
5400-0341 Whelen Arges super LED remote control spot light with 1 Manual added by JKOOGLER on 21-
light bar mount. If one is selected it will be located AUG-25
centered on cab roof light bar. If two are selected, they
will be located one each side of cab roof light bar offset
outboard as much as practical. The remote control(s)
installed accessible to driver and/or officer respectively.
CONTROLS / SWITCHES
1750-0034-1JK Switch, additional 12 volt/15 amp. Location and function: 1 Manual added by JKOOGLER on 21-
through multiplex display as a master switch for all cab AUG-25
and body scene lights (N/A for aerial lights).
1750-0034-S79 Switch, additional 12 volt/15 amp. Location and function: 1 Manual added by JKOOGLER on 21-
driver's side pump panel for air horn(s). AUG-25
1750-0838-0AC Rocker switch cap to be red. Switch: air horns. 1 Manual added by JKOOGLER on 21-
AUG-25
5100-0001-39T Switch circuit three way. Includes (1) additional switch. 1 Manual added by JKOOGLER on 21-
An additional switch required for more than two AUG-25
locations. Location: driver rear of body for rear scene
lights.
5100-0001-57C Switch circuit three way. Includes (1) additional switch. 1 Manual added by JKOOGLER on 21-
An additional switch required for more than two AUG-25
locations. Location: pump operator's panel for all 12v
flood / scene lights together labeled "ALL SCENE".
Page 29 of 36

Salescode Extended Description Qty Prebuild Changes Notes
5100-0001-5LZ Switch circuit three way. Includes (1) additional switch. 1 Manual added by JKOOGLER on 21-
An additional switch required for more than two AUG-25
locations. Location: officer's side overhead console for all
12v flood / scene lights together labeled "ALL SCENE".
5100-0001-5M0 Switch circuit three way. Includes (1) additional switch. 1 Manual added by JKOOGLER on 21-
An additional switch required for more than two AUG-25
locations. Location: driver's side overhead console for all
12v flood / scene lights together labeled "ALL SCENE".
5100-0006-198 Foot switch to control Q2B located driver's side. 1
5100-0029-L10 Stirrup style hose reel switch. Location: below tailboard 1
offset to officer side of B1.
5100-0036-0B0 Additional programming instructions: compartment lights 1 Manual added by JKOOGLER on 21-
to activate through park brake. Switch function is to turn AUG-25
off lights when brake is set, (if required).
5100-0036-0B1 Additional programming instructions: work lights to 1 Manual added by JKOOGLER on 21-
activate through park brake. Switch function is to turn off AUG-25
lights when brake is set.
5100-0036-13Q Additional programming instructions: hosebed light wired 1 Manual added by JKOOGLER on 21-
through cover in addiiton to standard. AUG-25
5100-0036-4UB Additional programming instructions: the alternating 1 Manual added by JKOOGLER on 21-
headlight option is to be programmed to the headlamp AUG-25
Halo circuit.
5100-0036-5IE Additional programming instructions: vista display 1 Manual added by JKOOGLER on 21-
screen(s) to default to "night mode" setting, and be AUG-25
manually brightened if needed.
5100-0165 Audible door ajar alarm wired through door ajar light. For 1
use with multiplex display(s) only.
5100-0257 Ramsey control with 15' cord for 2 arm ladder rack in 1 Manual added by JKOOGLER on 21-
addition to standard. Red/Black weatherproof push AUG-25
buttons at end of cord. Includes master switch adjacent
to control to activate control. Location to be as specified
by sales.
5100-0273 Weatherproof PKU switches on pump panel ipo toggle 1 Manual added by JKOOGLER on 21-
switches. AUG-25
5100-0274 Switch to override the warning light low power mode. 1 Manual added by JKOOGLER on 21-
Used inconjunction with 5600-0957 photocell. AUG-25
Page 30 of 36

Salescode Extended Description Qty Prebuild Changes Notes
CAMERAS / INTERCOM
5350-0107-762 Intercom base unit to be located behind officer's seat. 1 Manual added by JKOOGLER on 16-
MAR-26
5350-0319 FireCom wireless intercom kit to include a digital 1
intercom model 5100D, one (1) base transmit unit with
up to (5) radio/intercom only transmission and up to (5)
headset hooks shall be installed within the cab. Headsets
are not included and ordered separately (misc loose
equip)
5350-0516 Camera system FRC inView 360 HD. Includes 4 cameras 1
located front, rear, left and right and view select
button(s). Dealer/Customer to provide SD card(s) for
recording capability. Requires seperate multiplex color
display as the monitor. Note: cameras must be located as
high as possible with side cameras centrally located.
MISC ELECTRICAL
5110-0004 Alternating flasher for headlights. Not available on Ford 1
chassis.
5110-0017 Back-up alarm 97 dB. 1
5110-0018-751 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: L1 upper foward wall. AUG-25
5110-0018-752 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: L2 upper forward wall. AUG-25
5110-0018-753 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: L3 upper forward wall. AUG-25
5110-0018-755 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: R1 upper forward wall. AUG-25
5110-0018-756 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: R2 upper forward wall. AUG-25
5110-0018-757 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: R3 upper forward wall. AUG-25
5110-0018-848 12 volt 12 gauge constant hot lead (24" long) with 1 Manual added by JKOOGLER on 21-
ground wire. Location: centered on rear cab wall below AUG-25
seat support channel.
5110-0219-762 Blue Sea 12V power distribution module model 5032. 1
Location: behind officer's seat.
Page 31 of 36

Salescode Extended Description Qty Prebuild Changes Notes
5110-0219-A31 Blue Sea 12V power distribution module model 5032. 1
Location: behind driver's seat.
LIGHTS - AREA
5450-0690-00T FireTech 12" 12V bracket mounted light powder coated 2 Manual added by JKOOGLER on 21-
white with combo spot/flood optics. Includes switch in AUG-25
cab (driver and officer side facing lights switched
separately). Location:rear of body below hosebed
5450-0802-042 FireTech 18" 12V mini brow light with white housing, 30 2 Manual added by JKOOGLER on 21-
LED double stacked with flood optics. Includes switch in AUG-25
cab (driver and officer side facing lights switched
separately). Location: above L2/R2 compartments.
5450-0802-4TV FireTech 18" 12V mini brow light with white housing, 30 2 Manual added by JKOOGLER on 21-
LED double stacked with flood optics. Includes switch in AUG-25
cab (driver and officer side facing lights switched
separately). Location: front cab roof corners at 20 degree
angle mounting to allow number search.
ELBOWS
7400-0005 Chrome discharge elbow 2.5", 45 degree. 4
7400-0010 Chrome discharge elbow 4" 30 Degree. 4 Manual added by GFRANKLIN on
09-SEP-25
HOSE / NOZZLES
7700-0023 Booster Hose 100' x 1" Reeltex (Each) Niedner Reeltex 2
fabric booster hose with couplings.
GROUND LADDERS
7800-0016 Alco-Lite PEL-24' 2-section extension ladder. 1
7800-0032 Alco-Lite FL-10, 10' folding ladder w/safety shoes. 1
7800-0102 Alco-Lite DRL-16' roof ladder. 1
MISC LOOSE EQUIPMENT
7900-0014 DOT Required Drive Away Kit - Kit includes three (3) 1
triangular warning reflectors with carrying case. This kit
is for the end user and is to remain with the truck.
7900-0291 FireCom model UHW505 under helmet wireless radio 2
transmit headset.
7900-0295 FireCom model UHW503 under helmet wireless intercom 3
only headset.
Page 32 of 36

Salescode Extended Description Qty Prebuild Changes Notes
EXTERIOR PAINT
8100-0062 Paint Sample Spray Out - Dealer is responsible for 1
returning written approval prior to order release. Base
color of cab / chassis. Qty one in BOM will supply a pair
of paint samples (one for dealer/customer, one for
factory).
8100-0084 All applicable pump/pre-connect application modules are 1
to have a job color finish. Includes upper and lower
pump modules, crosswalk module and/or speedlay/pre-
connect module (as applicable). Rear mounted
body/pump module to be painted job color.
8100-0116 Rear body surface to have a sanded finish (not painted 1
job color). Includes hinged doors that do not have
discrete sales codes and removable panels.
8100-0551 Painted flag on cab grille. Details to be provided per 1 Manual added by GFRANKLIN on
customer specific requirements. ONLY available on 09-SEP-25
Typhoon and Cyclone cabs.
8100-0777 Paint rear body B1door job color. 1 Manual added by GFRANKLIN on
09-SEP-25
8100-0838 PPG brand paint will be used on the E-ONE supplied 1
components.
8100-0839 Paint Body - Small - For Pumpers, Rear Mounts, S/A 1 4006 White
Tankers and Rescues (non-metallic). Color:
8100-0851 Paint E-ONE cab - (non-metallic) paint. Color: 1 4006 White
INTERIOR PAINT
8150-0011 The interior of the cab to be painted multi-tone gray 1
finish.
8150-0024 The lower area of the painted cab interior door panels to 1
be masked off and left un-painted for reflective material.
PROTECTIVE COATINGS
8175-0086-000-13 The top perimeter of the bumper to have Black Scorpion 1
finish. Includes top lip, radius, and approx. 1" down.
Requires formed heavy duty bumper.
LETTERING
8200-0113 Scotchlite Letter (Each) upto 6" tall. The exact size, color 120
and location of the letters as specified by the customer.
Page 33 of 36

Salescode Extended Description Qty Prebuild Changes Notes
8200-0114 Scotchlite Letter (Each) upto 12" tall. The exact size, 10
color and location of the letters as specified by the
customer.
8200-0116 Shade and/or outline (EA) for letters as specified by the 130
customer.
STRIPING
8300-0042 White rubrail scotchlite insert. 1
8300-0144-000-J7 Chevron "A" style 6" 3M "Diamond Grade" striping full 1 Manual added by GFRANKLIN on
width on rear of body (does not include the B1 door). 09-SEP-25
Includes rear facing extrusions, panels and doors. Colors
to be Red/Fluorescent Yellow Green.
8300-0145-000-J7 Chevron "A" style 6" 3M "Diamond Grade" striping on 1
front bumper. Colors to be Red/Fluorescent Yellow
Green.
8300-0330 Single NFPA Scotchlite Stripe - up to 6" wide and straight 1
on cab and the body. Size, color and location as specified
by the customer.
8300-0334 Additional NFPA Scotchlite Stripe - up to 3" wide on cab 2
and the body. Design, size, color and location as
specified by the customer.
8300-0381 Yellow perimeter marking to indicate designated standing 1
/ walking areas above 48" high in compliance with NFPA
1900/1901 consisting of individual Reflexite diamonds
approximately 1" wide. Steps, ladders and areas with a
railing or structure at least 12" high are excluded from
this requirement
GRAPHICS
8400-0017-1V4 A customer logo supplied to E-ONE in a digital format. 6
Location: reference graphics layout drawing.
8400-0060 Graphics drawing showing striping, lettering and logos. 1
Requires E-ONE installed graphics.
8400-0067 E-ONE logo with grey backing on M6 series vertical tail 1
light housing (PR).
Page 34 of 36

APPENDIX B - WARRANTIES
Attach applicable documents here.
FTS Generic Apparatus Purchase Agreement Page 5

Salescode Extended Description Qty Prebuild Changes Notes
WARRANTY / STANDARD & EXTENDED
9100-0101 Meritor 5 year / unlimited miles parts and labor warranty 1
for front non-drive axle. Exceptions: MFS rated at 22,800
includes a 2 year / 200K miles parts and labor warranty
and a front drive axle includes a 2 year / unlimited miles
parts and labor warranty.
9100-0102 Meritor 5 year unlimited miles, parts and labor rear drive 1
single or rear drive tandem axle warranty.
9100-0117 General One (1) year or 24,000 Miles Limited Warranty 1
(RFW0001)
9100-0126 Custom chassis One (1) Year or 18,000 Miles Limited 1
Warranty (RFW0101).
9100-0132 Electrical One (1) Year or 18,000 Miles Limited Warranty 1
(RFW0201).
9100-0136 Body Structure Aluminum Ten (10) years or 100,000 1
Miles Limited Warranty (RFW0502).
9100-0138 Cab Structural Ten (10) Years or 100,000 Miles Limited 1
Warranty (RFW0602).
9100-0139 Plumbing and piping (Stainless Steel) Ten (10) years or 1
100,000 Miles Limited Warranty (RFW0800).
9100-0140 Paint and Finish (Exterior Clear coated) Ten (10) Years 1
Limited Warranty (RFW0710).
9100-0141 Cab Paint and Finish (Exterior Clear coated) Ten (10) 1
Years Limited Warranty (RFW0710).
9100-0151 Frame Rail Corrosion (Zinc Plate and Powder Coat) 1
Twenty Five (25) Years or 150,000 Miles Limited
Warranty (RFW0316).
9100-0165 Frame Rail Lifetime (50) Years or 250,000 Miles Limited 1
Warranty (RFW0305).
9100-0168 Regulated Emissions Systems Ten (10) Years or 450,000 1
Miles or 22,000 Engine Hours Limited Warranty
(RFW0144).
9100-0169 Regulated Emissions Two (2) Year or 24,000 Miles Tire 1
Warranty (RFW0145).
9100-0170 Regulated Emissions Five (5) Year or 100,000 Miles AC 1
Leak Warranty (RFW0146).
SUPPORT, DELIVERY, INSPECTIONS AND MANUALS
9300-0009 Manuals, Operator and Service in digital format. 1
Page 35 of 36

Salescode Extended Description Qty Prebuild Changes Notes
9300-0012 Pump panel approval drawings. Will be provided on 1
purchased units prior to construction.
9300-0016 Approval Drawings-Standard. 1
9300-0031 Dash/Console panel layout approval drawings. Will be 1
provided on purchased units prior to construction.
9300-0316 Fire Apparatus Safety Guide published by FAMA, latest 1
edition.
Page 36 of 36

FTS Generic Apparatus Purchase Agreement Page 6